Why Is My Blackstone Flaking?

Blackstone griddle seasoning flaking off in thin dark sheets with orange rust showing underneath

This post may contain affiliate links. Please read our Disclosure Policy

Quick answer:

Blackstone griddle flaking happens when the seasoning never bonded properly or something got underneath it. The usual causes are oil coats that went on too thick, carbon buildup from burnt food and grease, rust forming under the seasoning, or a shock of cold water on a hot griddle. To fix it, heat the griddle, scrape off everything loose, scrub with oil and a grill stone until it’s smooth, then re-season with 3 to 5 very thin coats.

Black Flakes in Your Eggs? Let's Fix That

Few things ruin a good breakfast faster than little black flakes in your scrambled eggs. If your cooktop looks like the photo above, with dark sheets curling up and orange peeking through underneath, take a breath. Your griddle isn’t ruined, and you definitely don’t need a new one.

Flaking is one of the most common Blackstone problems, and it almost always comes down to a handful of causes. Once you know which one you’re dealing with, the fix takes an afternoon, a scraper and a little patience.

Let’s figure out what’s going on with yours.

What Kind of Flaking Is It?

Not all flakes are the same, and the fix depends on which kind you’ve got. Here’s how to tell them apart:

  • Black, papery flakes that end up in your food: carbon buildup. Old layers of burnt grease, sauce and food bits that finally let go.
  • Thin dark sheets peeling up in patches: seasoning that never bonded to the steel, usually because the coats went on too thick.
  • Flakes with orange underneath: rust forming under the seasoning and pushing it up. That’s exactly what’s happening in the photo at the top.

Quick test: warm the griddle and wipe a spot with a little oil and a paper towel. Black means carbon or seasoning. Orange or brown means rust is involved.

Paper towel covered in black carbon flakes wiped off a Blackstone griddle

6 Reasons Your Blackstone Is Flaking or Peeling

1. The Seasoning Coats Were Too Thick

This is the big one. When you pour on too much oil, it can’t fully harden into seasoning. It stays a little soft and sticky, then cracks and peels off in sheets a few cooks later. Every coat should look almost dry by the time you’re done wiping it.

Puddle of oil on a Blackstone griddle, far too much for one seasoning coat

2. Carbon Buildup From Burnt Food and Grease

Every cook leaves a little something behind. If you don’t scrape the griddle while it’s still warm, those bits bake on, layer after layer, until they get thick enough to crack and fall into your food. Sugary sauces and marinades are the worst offenders. My 5-minute cleaning routine keeps this from building up.

3. Rust Is Lifting the Seasoning From Underneath

Moisture finds its way to the steel through thin spots and scratches, rust forms underneath and pushes the seasoning right off. Condensation under the lid, rain getting in and a griddle put away damp are the usual culprits. If you see orange, follow my guide on how to get rust off a Blackstone first.

4. Thermal Shock From Cold Water or Ice

Dumping ice on a ripping hot griddle looks great on social media, but it’s not so great for your seasoning. The sudden temperature drop can crack it. If you steam-clean, turn the burners down first and use a little warm water.

5. Acidic and Sugary Foods Sitting Too Long

Tomato sauce, lemon, vinegar, pineapple and sweet glazes slowly eat at seasoning, especially on a newer griddle. Cooking them is totally fine. Just don’t let them sit, and scrape them off right away.

6. The First Seasoning Didn’t Bond

If a new Blackstone starts flaking in the first few weeks, the first seasoning is usually to blame. The factory coating wasn’t cleaned off, the oil went on too thick, or the griddle wasn’t hot enough for each coat to smoke off completely. Some oils, like flaxseed, are also famous for flaking. Thin coats of a high smoke point oil fix it, and my seasoning guide walks you through it.

Is It Safe to Cook on a Flaking Blackstone?

A few flakes of carbon or old seasoning won’t hurt you, but they taste bitter and nobody wants them in their smash burgers. Rusty flakes are a different story, those you don’t want to eat. Either way, scrape off anything loose before you cook. Cooking over loose flakes just means they keep ending up on your plate.

How to Fix a Flaking Blackstone in 5 Steps

For patchy flaking you don’t need to strip the whole griddle. This takes about 45 minutes, and most of that is just letting the seasoning smoke.

Step 1: Heat It Up

Run the burners on medium for about 10 minutes. Heat softens the carbon and helps loose flakes let go.

Step 2: Scrape Off Everything Loose

Hold your scraper at a low angle and push off every flake, chunk of carbon and bit of loose rust. Work in long, steady passes. You’re only removing what’s loose, not gouging the steel.

Scraping flaking seasoning and loose rust off a Blackstone griddle with a metal scraper

Step 3: Scrub the Edges Smooth

Squirt on a little oil and scrub the flaked areas with a grill stone. The goal is to feather the edges so there’s no ridge between the bare spots and the good seasoning around them. If you can still feel a lip with your scraper, keep going.

Careful, the grill stone gets hot. It soaks up heat from the griddle while you scrub, and after a minute or two it can be too hot to hold with bare hands. Turn the burners down to low, wear heat-resistant gloves, or use a cleaning brick with a handle like the one in the Blackstone cleaning kit, so your fingers stay away from the hot steel.

Scrubbing a Blackstone griddle smooth with oil and a grill stone to remove rust and rough spots

Step 4: Wipe It Clean and Dry It

Wipe with paper towels until they come up black instead of orange or full of flakes. Then leave the burners on for a few minutes so every bit of moisture cooks off.

Wiping loosened rust residue off a Blackstone griddle with a towel

Step 5: Re-Season With Thin Coats

Wipe on a very thin coat of high smoke point oil or Blackstone griddle conditioner, let it smoke until it stops, and repeat 3 to 5 times. The bare spots will look lighter at first. They catch up after a few cooks, especially if you start with something fatty like bacon.

Wiping a thin coat of oil onto a clean Blackstone griddle

Here’s what you’re aiming for: dark, smooth and even, with no edges you can catch with a scraper.

Clean, dark and evenly seasoned Blackstone griddle cooktop

When the Whole Top Is Flaking

If the flaking is everywhere, or there’s more rust than seasoning, patching won’t hold. Strip it back to bare steel instead. Heat it, scrape it and scrub the whole top with oil and a grill stone (some people use a flap disc on an angle grinder for really heavy buildup, just go easy). Wipe until the towels come up clean, then do a full seasoning from scratch. My rust removal guide covers the heavy-duty version step by step.

How to Keep Your Blackstone From Flaking Again

  • Keep every coat thin. If it looks wet or shiny, wipe more off.
  • Scrape while it’s warm. Don’t let food and sauce bake on overnight.
  • Oil after every cook. A thin coat while it’s still warm protects the steel.
  • Skip the ice. Steam with a little warm water on lower heat instead.
  • Cook fatty food early on. Bacon and smash burgers build seasoning faster than anything.
  • Keep moisture off the cooktop. That’s how rust sneaks under your seasoning in the first place.

Once the griddle cools, I lay a silicone griddle mat over the cooktop. Rain, condensation, dust and bugs stay off the steel, so rust can’t sneak under the seasoning and start lifting it.

Blackstone griddle with an orange silicone griddle mat covering the cooktop
OZG and Chef Ember's Griddle Care are run by the same team.

Blackstone Flaking FAQ

Why is my new Blackstone flaking?

Usually the first seasoning went on too thick or the factory coating wasn’t cleaned off first. Scrape off the loose flakes, scrub the edges smooth and re-season with thin coats.

Why is my Blackstone chipping?

Chipping is the same problem as flaking, just in smaller pieces: bits of seasoning or carbon popping off. The causes and the 5-step fix above are the same.

Is it normal for a Blackstone to flake a little?

A few tiny carbon flakes now and then is normal on a well-used griddle. Big sheets peeling off means the seasoning didn’t bond or rust is getting under it.

Why is my Blackstone flaking after I seasoned it?

The coats were too thick or didn’t get hot enough to smoke off completely. Wipe each coat until it looks almost dry and heat it until the smoke stops.

Can I cook over the flaking?

Scrape off everything loose first. Cooking over loose flakes means they end up in your food, and they taste bitter.

Does ice cause a Blackstone to flake?

It can. A big temperature drop on a very hot griddle can crack the seasoning. Use a little warm water on lower heat instead.

Do I need to strip my Blackstone to bare metal?

Only if the flaking or rust covers most of the top. For patches, scrape, scrub the edges smooth and re-season just those spots.

Let’s fire it up! Chef Ember

How to Fix a Flaking Blackstone Griddle

Scrape off the loose flakes, smooth the surface with oil and a grill stone, rebuild the seasoning with thin coats, then keep it from flaking again.
Prep Time5 minutes
Active Time45 minutes
Total Time50 minutes
Keyword: blackstone flaking, blackstone seasoning flaking
Yield: 1 griddle

Equipment

  • Griddle scraper
  • Grill stone or griddle cleaning brick
  • Paper towels
  • Tongs or heat-resistant gloves
  • Silicone griddle mat (to cover the cooled cooktop)

Materials

  • High smoke point oil or Blackstone griddle conditioner

Instructions

Fix the flaking

  • Heat it up. Run the burners on medium for about 10 minutes to soften the flakes and any buildup.
  • Scrape off everything loose. Hold the scraper at a low angle and push off all the flakes, carbon and loose rust. Don’t try to save loose seasoning. If it lifts, it has to go.
  • Scrub it smooth. Add a little oil and scrub with a grill stone until the edges of the flaked spots feel smooth and blend into the seasoning around them. The stone gets hot, so use gloves or a handled brick.
  • Wipe and dry. Wipe with paper towels until they come up black instead of orange or full of flakes, then let the heat dry the steel completely.
  • Re-season thin. Wipe on a very thin coat of oil, let it smoke until it stops, and repeat 3 to 5 times. Thin, even coats bond to the steel. Thick coats turn sticky, and that is the number one reason seasoning flakes.

Keep it from flaking again

  • Go easy on the oil. After every cook, leave only a thin, almost dry coat. Puddles of oil build up into the sticky layers that peel later.
  • Cover the cooktop. Once it’s cool, lay a silicone griddle mat on the cooktop before you close the lid. It keeps moisture and grit off the new seasoning while it’s still building up, which is when it’s easiest to damage.

Notes

Whole top flaking? Strip it back to bare metal and do a full seasoning. My seasoning guide walks you through it.
Protect the fresh seasoning: new seasoning is thin and still building up, so moisture or grit sitting on it between cooks can undo your work. I keep a silicone mat flat on my cooktop whenever the griddle is cool. Mine is the OZG Silicone Griddle Mat, and it keeps the surface clean and dry until my next cook.
OZG and Chef Ember’s Griddle Care are run by the same team. As an Amazon Associate I earn from qualifying purchases.
Chef Ember cooking on a Blackstone griddle in the backyard

Hi, I'm Chef Ember

Some of my favorite memories are made around a hot grill with good food and even better company. For me, cooking outside isn’t just about the meal — it’s about connection, laughter, and those little moments that turn into lasting memories.

I share simple, reliable recipes and techniques to help you cook with confidence and enjoy the process.

Let’s fire it up.

Scroll to Top